SAQA All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.
SOUTH AFRICAN QUALIFICATIONS AUTHORITY 
REGISTERED UNIT STANDARD THAT HAS PASSED THE END DATE: 

Complete certificate of compliance for a single phase domestic installation 
SAQA US ID UNIT STANDARD TITLE
113898  Complete certificate of compliance for a single phase domestic installation 
ORIGINATOR
SGB Electrical Engineering & Construction 
PRIMARY OR DELEGATED QUALITY ASSURANCE FUNCTIONARY
-  
FIELD SUBFIELD
Field 12 - Physical Planning and Construction Electrical Infrastructure Construction 
ABET BAND UNIT STANDARD TYPE PRE-2009 NQF LEVEL NQF LEVEL CREDITS
Undefined  Regular  Level 4  NQF Level 04  5 
REGISTRATION STATUS REGISTRATION START DATE REGISTRATION END DATE SAQA DECISION NUMBER
Passed the End Date -
Status was "Reregistered" 		 2018-07-01  2023-06-30  SAQA 06120/18 
LAST DATE FOR ENROLMENT LAST DATE FOR ACHIEVEMENT
2024-06-30   2027-06-30  

In all of the tables in this document, both the pre-2009 NQF Level and the NQF Level is shown. In the text (purpose statements, qualification rules, etc), any references to NQF Levels are to the pre-2009 levels unless specifically stated otherwise.  

This unit standard does not replace any other unit standard and is not replaced by any other unit standard. 

PURPOSE OF THE UNIT STANDARD 
This unit standard is for persons in the Electrical Engineering; Generation; Distribution; Transmission, Construction and Renewable Energy Sector.

A person credited with this unit standard will be capable of:
  • Obtaining the completed inspection and test results of a single phase domestic electrical installation and be aware of any defects.
  • Using inspection documents obtained from the inspection and test and be able to use this information for completing the Certificate of Compliance.
  • Complete the written portion of the Certificate of Compliance with correct and accurate information.

    This unit standard will contribute to the full development of the learner within the electrical engineering and construction environment by providing recognition, further mobility and transportability within the field of Physical Planning and Construction. The skills, knowledge and understanding demonstrated within this unit standard are essential for social and economic transformation and upliftment within the electrical engineering and construction environment. This unit standard is a pre requisite for registration as an accredited person and does not give learners the legal right to complete a Certificate of Compliance. The registering authority will do registration as an accredited person. This unit standard may not cover the Explosion Industry. 
    		•

    LEARNING ASSUMED TO BE IN PLACE AND RECOGNITION OF PRIOR LEARNING 
    The following knowledge, skills attitude and / or equivalent:
  • Testing and inspection of single phase domestic installations
  • Wire and commission single phase domestic electrical circuits
  • Working knowledge of: SANS 10142-1
  • Awareness of the statutory requirements for non-compliance to the Occupational Health & Safety Act (Act 85 of 1993) 
    		•

    UNIT STANDARD RANGE 
  • Statutory Requirements may include, but are not limited to the Occupational Health and Safety Act 85 of 1993, SANS codes, Mineral and energy Act, Local Authority requirements, Manufacturers specifications and Worksite procedure
  • Domestic installations may include but are not limited to houses, flats and townhouse complexes and such, where the supply to the premises is single phase in both rural and urban environments
  • The Certificate of Compliance refers to a specific statutory document contained in the SANS 10142-1 code of practice
  • The ability to review and interpret an existing Certificate of Compliance for accuracy of the recorded information and compliance with the code 
    		•

    Specific Outcomes and Assessment Criteria: 

    SPECIFIC OUTCOME 1 
    Plan to complete the certificate of compliance from all the inspection and test data. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Collate all the inspection and test data and relevant information of the installation. 

    ASSESSMENT CRITERION 2 
    2. Obtain the Certificate of Compliance form in the correct format. 

    ASSESSMENT CRITERION 3 
    3. Transfer all the necessary data to the appropriate parts of the Certificate of Compliance. 

    ASSESSMENT CRITERION 4 
    4. Identify any noted defects from the collated data or code contraventions and report them to the user or owner of the installation. 

    SPECIFIC OUTCOME 2 
    Review of all the information on an existing certificate of compliance. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Scrutinise the recorded information for any abnormal or incorrect entries. 

    ASSESSMENT CRITERION 2 
    2. Evaluate the statements recorded for compliance with the code. 

    ASSESSMENT CRITERION 3 
    3. Test the recorded data against the code requirements, available drawings, circuit diagrams and any other relevant information regarding the installation. 

    ASSESSMENT CRITERION 4 
    4. Record any defects. 

    ASSESSMENT CRITERION 5 
    5. The values of readings from test is analysed for compliance with the code. 

    SPECIFIC OUTCOME 3 
    Review of a certificate of compliance against a specific installation. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Scrutinise the recorded information for any abnormal or incorrect entries. 

    ASSESSMENT CRITERION 2 
    2. Compare the recorded entries related to the features of the installation. 

    ASSESSMENT CRITERION 3 
    3. Verify the recorded information against the relevant sections of the code. 

    ASSESSMENT CRITERION 4 
    4. Record all defects and the specific code contravention. 

    ASSESSMENT CRITERION 5 
    5. Report to the user the non-compliant sections of the installation. 

    SPECIFIC OUTCOME 4 
    Complete a valid certificate of compliance by signing off the relevant sections of certificate. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    1. Transfer all the required information onto the certificate of compliance. 

    ASSESSMENT CRITERION 2 
    2. Keep a record of all the information on the contained on the certificate of compliance. 

    ASSESSMENT CRITERION 3 
    3. Relevant parties informed of outcome of verification. 

    ASSESSMENT CRITERION 4 
    4. Job completion is reported and the completed certificate of compliance is submitted according to OHS Act ekectrical installation regulations 


    UNIT STANDARD ACCREDITATION AND MODERATION OPTIONS 
    1. Anyone assessing a learner against this unit standard must be registered as an assessor with the relevant ETQA.

    2. Any provider offering learning that will enable achievement of this unit standard must be accredited as a provider through the relevant ETQA.

    3. Moderation of assessment will be overseen by the relevant ETQA according to the moderation guidelines in the relevant qualification and the agreed ETQA procedures. 

    UNIT STANDARD ESSENTIAL EMBEDDED KNOWLEDGE 
  • Working knowledge of SANS 10142-1 (Latest edition) and the Occupational Health & Safety Act (Act 85 of 1993)
  • Inspection documents and check lists pertaining to a single phase installation including the contents of a Certificate of Compliance
  • Understand the concepts of a single phase installation and its environment

    Knowledge that will help me understand and that I will be able to explain:
  • Types of material/equipment that may be used in electrical installations
  • Fault tracing procedures
  • Importance of safety for the user of the installation
  • The importance of accurately recording data and test results
  • Approved/SANS code relating to electrical equipment 
    		•

    UNIT STANDARD DEVELOPMENTAL OUTCOME 
    N/A 

    UNIT STANDARD LINKAGES 
    N/A 


    Critical Cross-field Outcomes (CCFO): 

    UNIT STANDARD CCFO IDENTIFYING 
    Identify and solve problems (identification of defects) 

    UNIT STANDARD CCFO WORKING 
    Work effectively with others (during the testing and inspection of an installation) 

    UNIT STANDARD CCFO ORGANISING 
    Organise and manage oneself (identification and selection of electrical equipment in the installation) 

    UNIT STANDARD CCFO COLLECTING 
    Collect, analyse, organise and critically evaluate information (during the inspection and testing of the installation) 

    UNIT STANDARD CCFO COMMUNICATING 
    Communicate (reporting of defects) 

    UNIT STANDARD CCFO DEMONSTRATING 
    Interpretation on statutory requirements 

    UNIT STANDARD ASSESSOR CRITERIA 
    N/A 

    REREGISTRATION HISTORY 
    As per the SAQA Board decision/s at that time, this unit standard was Reregistered in 2012; 2015. 

    UNIT STANDARD NOTES 
    Supplementary information:

    Specified requirements
    Specified requirements include legal and legislative specific requirements and are contained in one or more of the following documents:
  • SANS codes of practice for electrical installations
  • Occupational Health & Safety Act (Act 85 of 1993)

    Applicable statutory requirements
    A glossary of terms about the terminology of
    Context specific
    User manuals supplied manufacturers
    Specifications, agreements and policies and procedures 
    		•

    QUALIFICATIONS UTILISING THIS UNIT STANDARD: 
      ID QUALIFICATION TITLE PRE-2009 NQF LEVEL NQF LEVEL STATUS END DATE PRIMARY OR DELEGATED QA FUNCTIONARY
    Elective  72051   National Certificate: Electrical Engineering  Level 3  NQF Level 03  Passed the End Date -
    Status was "Reregistered"     		 2023-06-30  As per Learning Programmes recorded against this Qual 
    Elective  72052   Further Education and Training Certificate: Electrical Engineering  Level 4  NQF Level 04  Passed the End Date -
    Status was "Reregistered"     		 2023-06-30  As per Learning Programmes recorded against this Qual 
    Elective  48474   National Certificate: Electrical Engineering  Level 4  Level TBA: Pre-2009 was L4  Passed the End Date -
    Status was "Reregistered"     		 2009-02-18  Was EWSETA until Last Date for Achievement 


    PROVIDERS CURRENTLY ACCREDITED TO OFFER THIS UNIT STANDARD: 
    This information shows the current accreditations (i.e. those not past their accreditation end dates), and is the most complete record available to SAQA as of today. Some Primary or Delegated Quality Assurance Functionaries have a lag in their recording systems for provider accreditation, in turn leading to a lag in notifying SAQA of all the providers that they have accredited to offer qualifications and unit standards, as well as any extensions to accreditation end dates. The relevant Primary or Delegated Quality Assurance Functionary should be notified if a record appears to be missing from here.
     
    1. Better Best Agri Development 
    2. CLEAN HEAT ENERGY SAVING SOLUTIONS (PTY) LTD 
    3. ESKOM GENERATION - PALMIET PUMP STORAGE GRABOUW 
    4. KP ACADEMY (PTY) LTD 
    5. Majuba TVET College 
    6. Motheo TVET College 
    7. MSC ARTISAN ACADEMY 
    8. PCD College cc 
    9. POWER SYSTEMS TRAINING, CAPE TOWN 
    10. Protech Training (Pty) Ltd 


    All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.